Abstract: This paper introduces the simple diagnosis and precision diagnosis of rolling bearings for locomotives.
Key words: locomotive rolling bearing fault detection
1 Introduction
Bearings are the main components of locomotives, especially traction motors and axlebox
bearings. Their functions play a decisive role in safe transportation. When the locomotive is running online, once the bearing fails, the whole train will not run, blocking the traffic line. Especially when the passenger train fails, the negative impact is even greater. At the same time, once the locomotive bearing fails, it is very difficult to repair the locomotive. Therefore, it is very important to prevent and reduce the occurrence of locomotive bearing faults. Whether it is possible to detect the bearing with hidden troubles before the bearing is loaded, and to ensure that the qualified bearing accessories are on the car is the focus of this article {TodayHot}.
2 bearing failure
Severe damage of the bearing is often not caused by a single cause. However, under a combination of several aspects, a vicious cycle occurs under severe operating conditions, resulting in serious burning of the bearing. Therefore, after an accident, it is often difficult to judge What causes it, it also gives us some difficulties in formulating relevant measures. For the convenience of discussion, we first analyze the causes of bearing failures from several aspects.
2.1 Abnormal wear of the bearing
2.1.1 When the bearing is used for a period of time, the bearing inner ring, rolling element, cage, outer ring, raceway, etc. will produce certain defects and scars, resulting in poor lubrication of the bearing, causing heat generation of the bearing, long-term heating, Lead to: (1) dilution of bearing lubricants. (2) Accelerate the fatigue of the material and reduce the hardness. Due to the above reasons, a vicious cycle is further formed, and the overheating is accelerated to burn the bearing. Severe bearing inner ring displacement, rolling element out of round, collision heat, and finally welded together. Therefore, when running online, if {HotTag} finds that the bearing is severely heated and smokes, do not stop, but keep running to the front station, because the overheated bearing is in a molten state at this moment, once it stops cooling, it can no longer walk, blocking the positive line. .
2.1.2 It is very important for the oil supply maintenance of locomotive bearings, especially for the proper amount of oil to ensure that the bearing has good lubrication. It is easy to cause bearing failure due to lack of oil and excessive oiling. Poor lubrication and heat, more often it is easy to cause stirring and overheating, so it is necessary to properly supply oil during maintenance, and the lubricating grease of the bearing is also very important. Once the oil and other impurities and moisture are dropped, it will affect the normal swimming. Gap and build the necessary oil film.
2.1.3 The bearing is used for too long, which exceeds the service life of the bearing and is prone to fatigue of the material. The strong impact of the material causes the material to deform, causing the roller and the raceway surface to peel off and crush, resulting in poor lubrication. And the vibration is increased.
2.2 Installation impact on bearings
2.2.1 The inner clearance of the inner ring of the bearing does not match the interference of the shaft. It is also easy to cause bearing failure. The interference is large. It is easy to cause the inner ring of the bearing to crack due to excessive tensile stress. The interference is too small. It is easy to cause the inner ring of the bearing to "relax".
2.2.2 Bearing assembly with improper clearance, it is easy to cause
bearing failure, small clearance is easy to cause friction between the roller and the raceway. As the temperature rises, the bearing inner ring, rolling element, cage, outer ring The temperature of the end caps is not the same, there is a temperature difference between them, so the amount of expansion is also slightly different, which causes a further reduction of the matching clearance, and the heat generation of the bearing is added. If the clearance is too large, the vibration of the roller is increased, which aggravates the impact of the roller and the raceway. At the same time, the internal load distribution is uneven, the load bearing roller is reduced, and the central roller load is excessive.
2.2.3 When assembling the bearing, the bearing is not impacted by the copper hammer, which causes the cage to be deformed. The inner and outer rings of the traction motor bearing are not installed correctly or other reasons cause the axial traverse amount to disappear, causing the bearing shaft to squash.
